EMI shielding performance of electroless coated iron nanoparticles on graphite in low-density polyethylene composite for X-band applications

In the proposed work, an investigation of shielding effectiveness (SE) for varying compositions of Graphene, Multiwall carbon nanotubes (MWCNT), and Iron nanoparticles coated on Graphite (Fe@Graphite) was conducted in X-band (8.2 GHz–12.4 GHz). All these are mixed in an LDPE matrix. The nanomaterial was subjected to chemical characterization, i.e., Scanning electron microscopy (SEM), X-ray diffraction (XRD), and vibrating sample magnetometry (VSM). The shielding observed is dominantly due to absorption. The lattice structure which facilitates the shielding due to absorption was the hexagonal graphite structure on whose surface iron nanoparticles were embedded and used as the magnetic filler. At the same time, Graphene and MWCNT act as electrically conducting fillers. The Total shielding effectiveness(SE_T) was maximum for LDPE, MWCNT, Graphene, and Fe@Graphite, in the ratio of 50: 5: 25: 20 by weight %, and is 49 dB at 9.65 GHz for a sample thickness of 3 mm.     

搅拌速率对β-PbO_2-CeO_2-ZrO_2复合电极材料电化学性能的影响

为了提高三价铬镀铬工艺中阳极材料的性能,采用阳极氧化法制备了掺杂纳米颗粒的β-Pb O2-Ce O2-Zr O2复合电极材料。通过扫描电化学显微镜和析氧极化曲线的测量,考察了不同搅拌速率条件下制备的复合电极材料在硫酸盐体系三价铬镀液中的电催化活性,利用塔菲尔曲线考察了复合电极材料的耐蚀性,并辅以扫描电镜表征了电极材料的微观形貌。结果表明:当施镀搅拌速率为350 r·min-1时,所制备的复合电极材料具有结构致密、电催化活性高、耐蚀性强等特点。     

Transformation of hydrophobic surface into superhydrophobic surface by interfacial flower like silver films

Fabrication of superhydrophobic surface was achieved by electroless deposition of silver film and subsequent immersion into a mixture of stearic acid and cysteamine. The resultant superhydrophobic surface with flower and fall‐leaves like structure showed lotus leaf effect with the water contact angle of about 154° making copper surface water repellant. Copyright © 2014 John Wiley & Sons, Ltd.     

化学镀钴和超级化学镀填充的研究进展

随着半导体集成度的不断提高,铜互连线的电阻率迅速提高。当互连线宽度接近7 nm时,铜互连线的电阻率与钴接近。IBM和美国半导体公司（ASE）已经使用金属钴取代铜作为下一代互连线材料。然而,钴种子层的形成和超级电镀钴填充7 nm微孔的技术工艺仍是一个很大的挑战。化学镀是在绝缘体表面形成金属种子层的一种非常简单的方法, 通过超级化学镀填充方式, 直径为几纳米的盲孔可以无空洞和无缝隙的方式完全填充。本文综述了化学镀钴的研究进展,并分析了还原剂种类对化学镀钴沉积速率和镀膜质量的影响。同时, 在长期从事超级化学填充研究的基础上, 作者提出了通过超级化学镀钴技术填充7 nm以及一下微盲孔的钴互连线工艺。     

亚硫酸盐无氰电沉积金新工艺及机制

直接以氯金酸作为主盐、 羟基乙叉二膦酸（HEDP）作为镀液稳定剂和镀层细化剂、 结合添加剂, 组成亚硫酸盐无氰镀金新工艺; 研究镀液稳定性、 镀层形态及金电沉积机制。结果表明, HEDP可明显提升镀液稳定性;不含HEDP的亚硫酸盐镀金液中, 镀层呈棒状晶粒并随沉积时间延长而逐渐生长,导致镀层外观随镀层厚度增加由金黄色转变为红棕色。镀液含有HEDP时, 金晶粒形态由棒状转变为棱锥状, 且棱锥状晶粒随沉积时间延长生长速率较小, 镀层厚度为1 μm时仍呈现金外观。电化学实验表明金电沉积不经历成核过程。     

Flexible strain sensor with ridge-like microstructures for wearable applications

The flexible stretchable sensors have great potential for implementation in various applications, such as intelligent soft robots, health monitoring, and motion detection. However, most of the flexible stretchable sensors with microstructures and high sensitivities are fabricated by expensive templates and complex processes. In consideration of large-scale fabrication, a low cost and efficient way is in great demand. Herein, electroless plating on Nafion films with decent swelling ratios are proposed to fabricate stretchable sensors with wrinkle-structured electrodes. By adding isopropanol (IPA) to the electroless plating process, the H₂O-IPA sensor with larger swelling ratio shows deeper surface wrinkles, higher surface roughness, and better sensitivity to strain. At the same time, the H₂O-IPA sensor exhibit good durability (500 cycles). By mounting the sensor on the joint of human finger, the motion of the finger bending and even the bending degree can be accurately detected, indicating the potential use in the field of wearable devices and soft electronic skins.     

Ni(OH)2修饰的三聚氰胺泡沫用于可压缩超级电容器电极

通过化学镀和电化学镀的方法制备了一种Ni(OH)₂电化学活性材料修饰三聚氰胺泡沫(MF)可压缩骨架的超级电容器电极材料MF/Ni(OH)₂。MF/Ni(OH)₂可压缩电极材料表现出最佳的电容性能,例如循环稳定性(即使在40 mA/cm^-3的电流密度下经过2000次充放电循环后,可压缩电极仍能保持90.63%的初始电容)和可压缩稳定性(即使在压缩率为50%时,仍具有97.88%的电容保持率)。层状可压缩超级电容器由MF/Ni(OH)₂弹性材料作为阳极,镍/碳(Ni/C)为阴极以及实验室中常用的滤纸作隔膜材料组成。这种超级电容器装置在不同的压缩下表现出良好的电化学性能和优异的压缩稳定性。最后,使用可压缩的超级电容器来点亮LED灯,以展示其在柔性电子设备中的应用。这些优化的电化学和机械性能表明MF/Ni(OH)₂可作为可压缩超级电容器的应用中的候选电极。     

Selective separation of trace nickel(II) and gold(I) ions via hollow fiber supported liquid membrane enhanced by synergistic extractants D2EHPA/TBP

This work presents the selective and simultaneous separation of nickel (Ni²⁺) and gold ([Au(CN)₂]⁻) ions, in trace amounts, from alkaline solution via hollow fiber supported liquid membrane (HFSLM) technique. HFSLM is challengingly carried out in real rinse wastewater generated by the ENIG plating process. The influence of various chemical parameters, including the type of extractant and their concentrations, molar ratios of mixed extractant as well as type of strippant, are also studied. The organophosphorus extractant mixtures of D2EHPA and TBP provide a synergistic effect for target Ni²⁺ ions but has an antagonistic effect as regards the extraction of non-target [Au(CN)₂]⁻ ions. Compared to other inorganic acids, HCl is seen to be the most suitable strippant for the selective stripping. Results demonstrate that percentages of extraction and stripping of Ni²⁺ ions achieved 85.7 and 83.2%, respectively. In contrast, percentages of extraction and stripping of non-target [Au(CN)₂]⁻ ions attained 15.6 and 1.94%.     

聚合物材料表面化学镀铜的前处理研究进展

聚合物材料表面金属化在通讯、电子、航空航天领域具有重要应用. 化学镀铜是聚合物材料表面金属化的主要技术之一. 聚合物材料表面的前处理直接影响化学镀铜层的结合力及镀层平整度. 本综述详细介绍非导电聚合物材料的种类、组成以及性能, 并概述其表面化学镀铜前处理的研究进展.     

氮化钛微粉增强镍磷化学复合镀层的组织及其摩擦磨损性能研究

利用自蔓延高温合成法得到的氮化钛微粉制备了Ｎｉ－Ｐ－ＴｉＮ化学复合镀层，采用Ｘ射线衍射仪，扫描电子显微镜和电子探针分析了镀层的组织和结构，并在球－块摩擦磨损试验机上对镀层的摩擦学特性进行了研究，结果表明，ＴｉＮ微粉可使Ｎｉ－Ｐ化学镀层的组织明显细化，且能提高镀层的最佳时效硬化温度随着Ｎｉ－Ｐ－ＴｉＮ化学复合镀层中ＴｉＮ共析量的增摩擦系数逐渐降低并趋于稳定，耐磨性则存在的一个最佳ＴｉＮ含量；ＴｉＮ微